Ubbink Quadro Rectangular Water Feature Reservoir Kit with Grid & Insert

SKU: UBB-QUADRO-RECT-KIT
Size

Quadro 1 – 65 L, Quadro 2 – 90 L, Quadro 3 – 180 L

Brand

Build a concealed reservoir under a fountain, drilled stone or wall spout. The Ubbink Quadro kit includes the rectangular tank, its matching galvanised steel grid and a removable pump-access insert. Choose 65, 90 or 180 L. The range is rated up to 150 kg when the supplied assembly is correctly supported. Choose the pump, hose and decorative feature separately.

Price range: £119.99 through £229.99 (inc VAT)

The Ubbink Quadro rectangular reservoir kit gives you a hidden sump and a matching support under a self-contained fountain. The pump sends water up through a drilled stone, ornament or wall spout. The water then falls onto the covered basin and runs back into the tank. The straight sides make a rectangular sump useful beside steps, under a deck opening or at the foot of a wall. You can keep the finished feature compact while making the pump accessible from above.

Choose between Quadro 1, 2 and 3

Quadro rectangular kits supplied in the UK
Model and kit code Nominal capacity Approx. outer L Ă— W Ă— D
Quadro 1
PWK1720
65 L 750 Ă— 400 Ă— 300 mm
Quadro 2
PWK1730
90 L 790 Ă— 480 Ă— 300 mm
Quadro 3
PWK1740
180 L 800 Ă— 650 Ă— 380 mm
  • 65 L for a narrow planting strip or small bubbling stone. It is the 400 mm-wide option. Plot where water falls from the feature before choosing this footprint.
  • 90 L for more catchment at the same listed depth. Quadro 2 is 80 mm wider and 40 mm longer than Quadro 1. That can give you useful extra water and splash clearance where the available depth is still about 300 mm.
  • 180 L for a wider feature or a system with more water in circulation. Quadro 3 is only 10 mm longer than Quadro 2 on paper, but it is 170 mm wider and 80 mm deeper. Measure for the extra width before designing the surround.

Allow for the whole tank, the foundation and side support. The table gives approximate product sizes. Dry-fit the delivered tank and grid before making a finished cut-out.

What arrives with the kit

Each kit includes a black polyethylene tank, a galvanised steel grid to suit that tank’s lip and a lift-out insert over the pump opening. Match the kit to the reservoir model when replacing a part. Choose your feature, pump, delivery hose and fittings separately. The bare Quadro reservoir and replacement Quadro grid are available individually.

Check water volume and the load above the tank

Nominal capacity is the supplier’s size figure. Working capacity is the water you can use while still keeping the pump submerged and leaving room at the top. For perspective, 6 m of hose with a true 25 mm internal bore holds roughly 3 L when full. Also account for the water in the stone, bowl, spillway or return channel. A bowl or shallow run can hold much more than the hose. Leave a reserve for splash, evaporation and the water that drains back when the pump stops.

The supplier quotes a 150 kg maximum loaded weight for the matched kit. Count the feature, its water where it sits above the grid, and the wet stone or gravel it supports. Put the feature on the supported part of the grid and keep its load off the access insert. Use separate structural support for heavy or concentrated loads that exceed the assembly’s suitability. Keep the grid free of foot traffic.

Fit the reservoir and test it before finishing the surround

  1. Place the tank. Prepare a firm, level base with even support. Set the rim so splashes can fall back into the reservoir. Follow the supplied instructions for the sides and any backfill.
  2. Check servicing space. Face the access insert towards the side you can reach. With the grid seated, check that the pump and hose connector can be lifted out. Allow the hose to turn without kinking and protect the cable where it passes the edge.
  3. Choose the pump. Measure the lift from the operating water level to the outlet and allow for resistance in the hose and fittings. For compact features, compare the curves on the Oase Aquarius Universal Classic pump range. Match flexible pond hose to the pump and feature connections.
  4. Run and stop the feature. Fill and test at the intended flow. Watch the level once the line and feature have filled. Switch off and confirm the returning water stays below the overflow level. Correct splash losses and check access again before laying decorative stone.

Frequently asked questions

Can I use this in a raised feature?

The UK supplier lists above- and below-ground applications. In a raised build, support the filled tank evenly on a base designed for its full weight and keep the insert reachable.

Will the rectangular grid fit any Quadro tank?

Choose the grid for Quadro 1, 2 or 3 specifically. Each tank has its own rim and seating size.

Can the pump be changed without lifting the feature?

The removable insert gives access if the pump, outlet adaptor and hose can pass through the opening. Test access before positioning the feature and covering the grid.

How do I work out which pump to buy?

Start with the outlet manufacturer’s required flow. Compare pump curves at your actual lift and hose run, then check the pump body and fittings fit through the insert.

Can I have a circular opening instead?

For a circular surround, compare the Ubbink round reservoir kits. For longer streams or larger hidden storage, browse our water feature reservoirs and pump vaults.

Products related to the Ubbink Quadro Rectangular Water Feature Reservoir Kit with Grid & Insert

Ubbink Quadro Rectangular Water Feature Reservoir Kit with Grid & Insert Reviews

Reviews

There are no reviews yet.

Be the first to review “Ubbink Quadro Rectangular Water Feature Reservoir Kit with Grid & Insert”