Ubbink Square Water Feature Grid

SKU: UBB-SQUARE-GRID
Size

600 Ă— 600 mm, 800 Ă— 800 mm, 1000 Ă— 1000 mm

Brand

A galvanised steel grid for a custom square water feature reservoir. Choose 600, 800 or 1,000 mm. The side cut-out leaves access to the pump and can be used for the pipe route. The supplier quotes up to 140 kg when the grid is suitably supported. Order the matching access insert separately.

Price range: £77.99 through £193.99 (inc VAT)

The Ubbink square water feature grid is a steel cover for the supported opening of a custom reservoir. It can sit over a properly supported blockwork or timber surround and provide a surface for a decorative feature and its stone dressing. Returning water passes through the open grid into the sump. A cut-out along one side gives access to the pump and can also provide a route for the hose. Choose the side that will be easiest to reach once the feature is finished.

Choose the grid size from the supported opening

Square Ubbink grid options
Approx. grid size Product code What to check first
600 Ă— 600 mm PNW1840 Room for the feature foot and service access
800 Ă— 800 mm PNW1850 Clear span, perimeter support and return area
1000 Ă— 1000 mm PNW1860 Support on the larger opening and room to reach the hatch

The table gives the size across the grid. Measure the opening between supports separately. Allow the bearing required by the installation so the grid rests securely. Check both sides and the diagonals of the finished frame. If a nominally square opening is out of square, the corners may need adjustment before a grid will seat flat. Use the delivered grid to check the fit before fixing the top course or surrounding paving.

Design the support for the complete load

Landscape Plus quotes up to 140 kg for these square grids. That figure relies on correct support. Plan for the weight of the fountain, plinth and wet decorative material, including any water held above the grid. A small base can concentrate a load even when its total weight looks acceptable. Keep the feature over the main, supported grid and clear of the access opening. Provide an independent bearing for any heavy masonry, visitor traffic or load that needs separate structural support.

Make the support firm and level around the grid. Protect pond liner from sharp grid ends, fittings and masonry edges. Make sure the retaining structure and overflow are appropriate for the filled reservoir. For a timber surround, use a frame suitable for the damp installation and make its load path clear before filling the sump.

Leave a genuinely usable pump opening

The access cut-out sits at the side. Check that it is wide enough for the pump, outlet fitting and any removable pre-screen. Set out the hose and power cable so servicing can be done from the accessible edge. Try lifting the pump while the grid is in place. The matching Ubbink 200 mm square access insert is available separately. Check the opening and its seating edges on your grid before ordering one, particularly on an existing installation.

Keep water returning to the sump

Size the basin and its return area for the flow coming off the feature. Gravel or decorative stone should allow water through the grid and should stay easy to lift around the hatch. Test at the intended flow and switch the pump off to check the returning water stays inside the reservoir. When splash repeatedly lands beyond the side, increase the catchment or revise the flow before finishing around the feature. Leave a clear route for routine removal of sediment and leaves.

Frequently asked questions

Is the 200 mm access insert included?

Select the insert separately if you want to fill the access opening. Check the opening and support lip before ordering.

Can I choose a grid using the reservoir’s litre capacity?

Measure the actual supported opening. The grid size describes the top cover and provides no capacity figure for the tank below.

Can the opening take both the hose and an access cover?

Check the way the hose passes the side cut-out with the insert fitted. Keep the route clear so the insert can be removed and the cable and hose do not get trapped.

Would a square grid suit a Ubbink round or Quadro tank?

For a manufactured Ubbink tank, choose the round grid or rectangular Quadro grid for its exact model. Use the square grid where your custom support is designed for it.

Where can I compare ready-matched kits?

Browse the water feature reservoir range if you want a reservoir and cover supplied together.

Products related to the Ubbink Square Water Feature Grid

Ubbink Square Water Feature Grid Reviews

Reviews

There are no reviews yet.

Be the first to review “Ubbink Square Water Feature Grid”