AquaForte Impermax solvent 4 kg

SKU: LS1006
Brand

Supplier SKU

LS1006

Supplier Availability

In stock

Pack Size

4kg

Product Type

Impermax Solvent

4kg AquaForte Impermax Solvent for specified coating preparation and compatible tool cleaning. Use only as permitted by the exact resin instructions. Solvent does not increase finished lining coverage and is not a pond sealer or a substitute for primer.

£64.82 (inc VAT)

Out of stock

Out of stock

AquaForte Impermax Solvent 4kg

A compatible system solvent for specified Impermax preparation and tool cleaning

AquaForte Impermax Solvent is supplied in a 4kg pack for use within the Impermax liquid rubber pond liner system. It is a supporting material for the uses permitted by the coating instructions, including cleaning appropriate tools while resin remains uncured and specified dilution operations. It is not a pond lining, not a stand alone waterproof sealer and not a substitute for the appropriate primer.

Solvent choice matters because an unsuitable thinner can interfere with a polyurethane coating. The Impermax manual specifically excludes unapproved solvents and alcohol containing materials from resin dilution. Do not substitute white spirit, a general purpose thinner or a household cleaner merely because it appears to dissolve paint. Use the named compatible product and the instructions for the precise resin formulation being applied.

Does solvent increase Impermax coverage?

No: solvent does not increase the amount of waterproof membrane in the tin. It can alter application consistency where the specification permits, but the required resin consumption and finished film thickness remain. The pond lining should still be calculated from the coating quantity, with approximately 2kg of membrane resin per square metre as the normal planning basis for the system described on our liner pages.

A 4kg solvent pack therefore has no useful stand alone pond coverage figure in square metres. Consumption depends on the authorised dilution method, the amount of resin involved, the equipment and cleaning requirements. It is also a pack sold by mass; do not assume 4kg is the same as four litres when measuring a mixture. Use the units and measuring method specified for the actual products.

When is dilution appropriate?

The general Impermax application manual describes limited solvent addition for particular preparation and application methods. It gives 5% as an ideal dilution level where dilution is called for, with a maximum of 10%, and warns that excessive solvent affects the membrane’s elongation. These figures are limits within a specified procedure, not an instruction to thin every tin of pond liner.

Different Impermax formulations and primers have different requirements. Some are supplied ready for use, and the AquaForte ST instructions differ from the general resin mixing instructions. Check the coating label and current technical sheet before adding anything. Where the dilution basis or exact version is unclear, establish that specification first instead of guessing an amount from the pack weights.

Do not use solvent as a shortcut around surface preparation, dampness or the need for primer. A diluted resin coat described for one porous surface is not automatically the correct treatment for tiled, metal or damp substrates. The surface must be assessed and the appropriate system selected before application begins.

Using solvent for tool cleaning

Prepare your cleaning area before starting the coating work. The manufacturer’s application guidance calls for tools to be cleaned promptly with compatible polyurethane solvent after use. Cleaning is most effective before the resin cures; leaving brushes, rollers or metal tools until the next day makes the job substantially harder. Check the tool manufacturer’s compatibility information too, particularly for plastic components, seals and sprayer parts.

  1. Remove excess coating first. Keep usable resin separate from cleaning waste and avoid returning contaminated material to the original coating tin.
  2. Use a suitable cleaning container. Keep the work controlled and follow the solvent safety sheet, including ventilation, gloves and eye protection.
  3. Clean before cure. Do not rely on solvent to restore an already hardened coating or to prepare a cured pond liner for repair without the prescribed procedure.
  4. Collect the waste. Keep solvent and resin residues out of drains, soil and pond water, and dispose of them through the appropriate waste route.

Drying, recoating and the pond filling schedule

Solvent evaporation is not the same process as achieving a fully cured waterproof membrane. A coat may look dry or be ready for the next coat while the completed lining still needs considerably longer before water is introduced. Adding solvent is not a way to shorten the pond filling schedule; use only the approved accelerator system if one is actually specified for the coating and conditions.

The AquaForte pond instructions give approximately 15 days after the final membrane coat before filling, once the solvent has evaporated and the lining has cured appropriately. Conditions such as low temperatures, poor ventilation and thick areas can extend the wait. Use the current instructions for the supplied resin and inspect the coating rather than treating the calendar alone as proof that it is ready.

After the specified cure, rinse and drain the pond before its final fill. Do not clean a finished fish pond with solvent as part of routine maintenance. If a repair or overcoating operation is required, follow the manufacturer’s surface preparation method for the cured membrane and remove fish before the work.

Planning a practical application kit

Order solvent alongside the correct membrane quantity, the specified primer and any reinforcement needed at corners and penetrations. This avoids interrupting an application while trying to find compatible cleaning materials. Keep coating tools and cleaning tools organised separately so that contaminated solvent is not accidentally mixed into fresh resin.

Store the labelled container securely in accordance with the safety sheet and away from ignition sources. Read the handling instructions before opening it, and provide effective ventilation throughout use. The product is intended for controlled coating work, not for dosing into pond water or for cleaning equipment while connected to a stocked pond.

Plan the rest of your Impermax system

AquaForte Impermax grey in 2.5kg and 10kg, AquaForte Impermax black in 2.5kg and 10kg, AquaForte Impermax PU primer 4 kg. Browse the AquaForte Impermax range to put together the coating and preparation materials for your pond.

Read the Impermax application manual for authorised solvent use and the safety data sheet supplied with the product for handling and disposal. Always match these instructions to the resin version on your tin.

Products related to the AquaForte Impermax solvent 4 kg

AquaForte Impermax solvent 4 kg Reviews

Reviews

There are no reviews yet.

Be the first to review “AquaForte Impermax solvent 4 kg”