AquaForte Impermax Black Liquid Rubber Pond Liner

SKU: AQUAFORTE-IMPERMAX-BLACK
Brand

Pack Size

2.5kg, 10kg

Product Type

Liquid Rubber Pond Liner

Colour

Black

AquaForte Impermax black liquid rubber pond liner in 2.5kg or 10kg. Finished coverage is approximately 1.25m² or 5m² respectively at 2kg/m² total, before allowances. Choose your size below and follow the full preparation, coating and curing guidance.

Price range: £42.80 through £181.99 (inc VAT)

AquaForte Impermax Black Liquid Rubber Pond Liner

A seamless polyurethane lining with practical application, coverage and curing guidance

AquaForte Impermax black is a liquid rubber pond liner supplied here in a choice of 2.5kg or 10kg. Select the pack size to see its price and availability. Both sizes contain the same colour of polyurethane membrane for creating a flexible, seamless lining on a correctly prepared pond shell.

Choose black for a dark finished pond lining. It can be applied over a contrasting grey coat within the approved system, making missed areas easier to identify during application. The coating follows shelves, curves and details without the folds of a sheet liner. Its elasticity accommodates small movements in a suitable support, but it does not repair an unstable structure.

Choose a size and calculate finished coverage

Plan on approximately 2kg/m² across the complete membrane build. At that rate, the 2.5kg pack covers approximately 1.25m² and the 10kg pack approximately 5m². These are finished lining areas, not coverage per coat. Allow additional material for roughness, reinforcement, detailing and wastage; primer is separate.

Black Impermax size options
Pack size Finished coverage at 2kg/m²
2.5kg Approximately 1.25m²
10kg Approximately 5m²

Measure the floor, every wall, shelves, steps and returns. For a rectangular pond, add length Ă— width to twice length Ă— depth and twice width Ă— depth. A pond 2m long, 1m wide and 1m deep has 8m² of internal surface, requiring 16kg of membrane before allowances. A floor-only calculation would miss most of that area. Choose enough packs to complete all coats rather than stretching a short quantity too thin.

How many coats of Impermax are needed?

Use several even coats to reach the specified overall consumption and membrane thickness. The supplier manual describes two to three coats, while the AquaForte pond guidance recommends three to four coats on walls where needed. For brush or roller work, plan for around three coats, adding another where the vertical surface or detailing requires it. Two thin decorative coats are not sufficient simply because the surface looks covered.

A total of approximately 2kg/m² is a useful pond planning basis; the supplier manual specifies a minimum finished membrane thickness of 1.6mm. Dividing 2kg/m² across three coats means roughly 0.67kg/m² in each coat. Weighing or allocating the resin to measured areas helps control application. Contrasting black and grey coats can make missed patches easier to see, but colour coverage alone does not measure film thickness.

Preparing the pond and choosing a primer

Empty the pond and keep fish elsewhere throughout preparation, coating and curing. The shell must be sound, even and free from dirt, algae, grease, loose paint and powdery cement residue. Allow new cement or repair mortar to cure and dry as specified for that material. Smooth sharp edges and repair defects before coating; a liquid membrane follows surface irregularities rather than hiding them.

Concrete, mortar, ceramics and suitable fibreglass surfaces require the correct preparation and adhesion checks. Existing coatings, waterproofing admixtures and glossy surfaces need particular care. A small trial area is useful before committing the whole pond. Moisture within the substrate can cause loss of adhesion or blisters, so investigate dampness rather than sealing over it.

Primer choice depends on porosity and moisture. Impermax PU Primer is the adhesion primer described for suitable smooth, nonporous surfaces; it is not the same as Humidity Primer. Where a moisture barrier is required, use the specified Humidity Primer system. A primer does not make a wet, waterlogged or structurally unsound surface ready for coating.

Applying the liquid rubber pond liner

  1. Plan a dry working period. Avoid rain, condensation, frost and hot surfaces in strong sunshine. Normal application planning should stay above 5°C and below 30°C; specialist low temperature use with additives needs the exact product instructions.
  2. Prime and detail first. Follow the primer’s own coating window. Reinforce wall to floor junctions, penetrations and other critical areas with the specified Geomax fleece embedded in wet resin, then fully encapsulate it.
  3. Check the tin before preparing the resin. Standard Impermax instructions describe gentle, low speed mixing and letting entrained air escape. Impermax ST instructions specifically say not to mix. Follow the label for the formulation supplied; do not apply one version’s mixing method to another.
  4. Coat walls before the floor. Use suitable solvent resistant short pile rollers and brushes for details. Spread controlled, even layers without leaving pools. On steep surfaces, use only the approved reinforcement or thickening system where specified.
  5. Inspect between coats. Deal with pinholes, bubbles and missed areas before covering them. Let each coat reach the condition required for recoating and keep contamination off the surface.

Drying time between coats versus full curing time

Temperature, humidity, ventilation and film thickness affect drying. Supplier headline figures of around 4–6 hours in summer and 12–24 hours in cooler conditions are broad guides, not a guaranteed timetable. The application manual also shows longer intervals in some conditions. A surface that feels dry is not necessarily cured through or ready for permanent immersion.

For pond filling, plan around 15 days after the final coat under suitable curing conditions. The AquaForte pond instructions give approximately 15 days for solvent to evaporate before filling. Cold, thick or poorly ventilated areas can take longer. Follow the current instructions supplied with your batch if these specify a different schedule; do not use the short between-coat figure as the fish return time.

Check the complete lining for soft spots, defects and incomplete cure, then rinse and drain before the final fill. Prepare the replacement water appropriately and confirm suitable water conditions before returning fish. Keep ventilation effective throughout application and cure, and follow the product safety sheet for gloves, eye protection and respiratory protection. Solvent vapour and ignition sources must be kept apart.

Common questions before ordering

Can I dilute it to cover more area? No. Adding solvent does not add waterproofing material. Use Impermax Solvent only for the applications and dilution levels permitted in the exact system instructions.

Can I coat a leaking pond without draining it? This is a lining operation on a prepared surface, not an underwater patch treatment. Identify the cause of the leak and repair the supporting structure where necessary.

Is it ordinary pond paint? Although applied with similar tools, Impermax is built up to a specified membrane thickness. Treat it as a liquid lining system rather than a thin colour coat.

Complete your liquid liner system

Compare Impermax grey in 2.5kg and 10kg sizes, choose the correct Impermax PU Primer where specified, and have compatible Impermax Solvent available for approved uses. Browse the Impermax coating range for the supporting products.

Application documents

Read the Impermax application manual and AquaForte Impermax pond instructions alongside the label and safety sheet supplied with your order. Product versions have different preparation instructions, particularly ST mixing, so check the actual tin before starting.

Products related to the AquaForte Impermax Black Liquid Rubber Pond Liner

AquaForte Impermax Black Liquid Rubber Pond Liner Reviews

Reviews

There are no reviews yet.

Be the first to review “AquaForte Impermax Black Liquid Rubber Pond Liner”