AquaForte Impermax PU primer 4 kg
| Brand | |
|---|---|
| Supplier SKU | LS1008 |
| Supplier Availability | In stock |
| Pack Size | 4kg |
| Product Type | Impermax Pu Primer |
4kg AquaForte Impermax PU adhesion primer for suitable smooth, nonporous surfaces beneath the membrane. Manufacturer guidance: 200–300g/m², giving roughly 13.3–20m² theoretical coverage. PU Primer and Humidity Primer have different roles; use the correct preparation system.
£105.96 (inc VAT)
Out of stock
Out of stock
AquaForte Impermax PU Primer 4kg
An adhesion primer for suitable smooth surfaces beneath an Impermax liquid rubber pond liner
AquaForte Impermax PU Primer prepares appropriate nonporous surfaces for the Impermax waterproofing membrane. This 4kg pack is a preparation product, not the final liquid rubber pond liner. Its role is to help the coating bond to a suitable substrate where the surface itself offers little absorption. It belongs underneath the specified Impermax resin system rather than being left exposed as the pond lining.
Choosing the correct primer starts with the surface you actually have. Glazed tiles, ceramics and suitable metal surfaces differ from porous concrete, and a dry surface differs from one containing trapped moisture. The Impermax application manual identifies PU Primer for nonporous substrates including ceramics, tiles, glass, aluminium and steel. Existing finishes, contamination and the condition of the supporting material still need assessment and a trial adhesion check.
Coverage from a 4kg pack
The supplier application manual gives approximately 200–300g/m² for PU Primer on the stated nonporous surfaces. Calculated from that rate, a 4kg pack provides around 13.3–20m² of theoretical coverage. Allow for the actual substrate, detailing, tools and wastage. This is primer coverage only; it must never be used to calculate how far the separate waterproof membrane will go.
For example, 10m² at 200g/m² requires 2kg of primer, while the same area at 300g/m² requires 3kg. These calculations help with ordering and application control, but they do not decide which rate is suitable for your particular surface. Measure walls, floor, shelves and returns, then apply the rate specified for the assessed system. A large enough primer pack does not mean you have bought enough liner resin.
PU Primer and Humidity Primer are different products
PU Primer is specified to promote adhesion on appropriate smooth surfaces. Humidity Primer serves a different purpose where the system needs to manage moisture and vapour from the substrate. They should not be treated as interchangeable because both have the word primer in their names. An apparently dry tiled surface may still conceal dampness underneath, so surface appearance alone is not a reliable specification.
If there is rising moisture, saturated masonry, trapped water or an unknown old coating, resolve the substrate condition and correct system before application. Adding extra coats of PU Primer is not a substitute for the required moisture barrier. Equally, no primer can make unstable tiles, loose render or a moving crack into a sound base. Repairs and any structural work belong before the coating stages.
Preparing and applying the primer
- Assess and prepare the surface. Remove loose material, dirt, algae, grease and incompatible residues. Check that existing finishes are firmly attached and suitable for overcoating.
- Complete repairs and detailing plans. Smooth sharp edges and decide how drains, pipe penetrations, corners and wall to floor joints will be incorporated into the membrane system.
- Check adhesion. On an unfamiliar substrate, carry out the trial specified in the system guidance rather than treating the full pond as the test area.
- Apply an even primer film. Use tools compatible with the product and control consumption against the measured area. Follow the tin’s preparation and safety instructions; do not thin it with an improvised solvent.
- Overcoat within the specified window. Have the membrane, tools and prepared work area ready before priming a large section.
Drying and overcoating time
The supplier’s Impermax installation manual specifies between 2 and 4 hours between PU Primer and Impermax. Treat that as the stated system window, alongside the current primer label and site conditions. It is not a promise that every surface will be ready after exactly two hours. Temperature, humidity and the condition of the film matter, so check the instructions supplied with the actual product before starting.
Work in manageable areas if you cannot apply the membrane to the entire primed surface within the required time. If the window is missed, stop and establish the correct preparation for overcoating rather than assuming a late coat will bond equally well. Keep dirt, water and foot traffic away from the prepared area while it waits for the membrane.
When can the pond be filled?
The primer’s short overcoating window is not the pond’s return to service time. After priming, the full waterproof membrane still has to be applied at the required thickness and allowed to cure. The AquaForte pond instructions allow approximately 15 days after the final membrane coat before filling, with suitable conditions and complete solvent evaporation. The current membrane instructions and actual cure govern this stage, especially during cold weather or in sheltered corners.
Inspect the completed system, rinse and drain as instructed, and prepare suitable water before fish return. Do not expose primer alone to pond water as though it were the finished liner. Primer, membrane coats and the final cure are separate stages with separate purposes.
Storage, tools and safe use
Keep the product in its labelled container and follow its storage temperature and use by information. Plan the work so that opened materials are used within their stated working life. Consult the safety data sheet for ventilation, protective equipment and handling requirements. Keep people and animals away from the work area and avoid sources of ignition where solvent based materials are being used.
Have compatible cleaning materials ready before opening the tin. Clean tools according to the product instructions and collect residues for appropriate disposal. Never wash coating residues into the pond, surface water or a drain. The separate Impermax solvent is a system product, so confirm suitability for the particular tool or material before use.
Plan the rest of your Impermax system
AquaForte Impermax grey in 2.5kg and 10kg, AquaForte Impermax black in 2.5kg and 10kg, AquaForte Impermax solvent 4 kg. Browse the AquaForte Impermax range to put together the coating and preparation materials for your pond.
For the substrate categories, application rates and PU Primer coating window, consult the Impermax installation manual. The current instructions on the supplied product take precedence where the formulation or specification has changed.



Reviews
There are no reviews yet.