Oase HeatUp 100 Adjustable Aquarium Heater

Categories:
SKU: 42726
Brand

Manufacturer SKU

42726

Aquarium size guide

100 litres maximum

Rated supply

230 V / 50 Hz

Power

100 W

Cable length

1.5 m

Diameter × height

23 × 245 mm

Temperature setting

18–32°C

Water type

Freshwater and saltwater

Adjustable 100 W Oase aquarium heater for freshwater or marine tanks up to 100 litres, with an 18–32 °C setting range, mounting bracket and 1.5 m lead.

£19.91 (inc VAT)

Steady, adjustable heating for an aquarium

The Oase HeatUp 100 Adjustable Aquarium Heater is a submersible, thermostatically controlled heater for freshwater and saltwater aquariums. It is rated at 100 W and Oase gives an aquarium-size guide of up to 100 litres. A temperature control allows a setting from 18 to 32 °C, while an indicator light shows when the heating element is operating.

The light going out after the aquarium has reached the set temperature is normal: the thermostat switches the element on and off as heat is needed. An independent aquarium thermometer is still important, because the dial setting is a starting point rather than a substitute for checking the water where the animals live.

Choosing a suitable size

The HeatUp 100 is rated at 100 W for aquariums up to 100 litres. Compared with the 50 W HeatUp 50, it has a higher rated output and a longer 245 mm housing, so confirm the available depth and the space for the bracket. The tank-size figures are guides. Consider the actual water volume, the coldest room temperature, the desired water temperature and the needs of the inhabitants. A heater that cannot deliver sufficient heat for the temperature difference may run for long periods without reaching the setting.

The stated dimensions are 23 × 245 mm, diameter by height. Check there is room to mount it at the required immersion depth without trapping it behind decorations or blocking circulation. The heater comes with its mounting bracket and a 1.5 m power cable; the aquarium, thermometer and any filter or retrofit adapter are separate.

Installation and safe first use

Use the holder to position the heater in a filled aquarium where water circulates freely, following the orientation and minimum-immersion marking in the supplied instructions. Do not energise the heater while it is dry or below its required water level. Arrange a drip loop in the power lead and keep the electrical connection away from splashes.

Oase’s HeatUp manual says to leave the heater in the aquarium for approximately 30 minutes before switching on so the thermostat can adjust to the water. Set the control, allow the aquarium temperature to settle, and check with a separate thermometer. If the measured temperature differs, first check water circulation and then follow the manual’s calibration instructions rather than assuming the dial is exact.

Before a water change or any work that could expose the heater, disconnect it and the other aquarium electrical equipment. Allow the heater to cool before lifting it from the water: its glass surface can remain hot after the power is removed.

Using a compatible filter

For an Oase FiltoSmart 100 external filter, Oase identifies the ThermoFit 100 adapter, article 45047, for a compatible heater retrofit. The filter and adapter are separate. The BioPlus Thermo 100 is a different corner-filter package that already includes a HeatUp 100; do not buy an external ThermoFit adapter for it.

When a manufacturer-approved filter installation places the heater inside the filter, the Oase instructions say to switch on the heater only when the filter is completely filled, running and circulating water continuously. Follow the instructions supplied with both pieces of equipment and isolate both electrical supplies before servicing them.

Specifications and common questions

Specification Detail
Manufacturer / article Oase / 42726
Heater type Adjustable submersible aquarium heater
Aquarium size guide Up to 100 litres
Rated power 100 W
Temperature setting 18–32 °C
Dimensions (diameter × height) 23 × 245 mm
Rated supply 230 V / 50 Hz
Power cable 1.5 m
Water type Freshwater and saltwater
Mounting Bracket included

Does it run at 100 W all the time? No. The heating element switches on and off under thermostat control. The actual time it runs depends on room conditions, target temperature, water volume and heat loss.

Is a thermometer included? No. Use a separate thermometer to check the water after installation and periodically afterwards.

Can it be used in saltwater? Oase lists the HeatUp 100 for freshwater and saltwater; install and maintain it according to the supplied instructions.

Browse more aquarium equipment and accessories.

Oase HeatUp 100 Adjustable Aquarium Heater Reviews

Reviews

There are no reviews yet.

Be the first to review “Oase HeatUp 100 Adjustable Aquarium Heater”